2015-2020 Chevrolet Tahoe on all-terrain tires - upper control arms comparison
N

Next Level Performance

November 15, 2026 โ€ข 9 min read

Our Verdict

For most leveled or lifted 2015โ€“2020 Tahoe, Yukon and Suburban builds, the Superlift 3600 cast upper control arms are the best-value pick at around $250. Choose the ICON 78601DJ Delta Joint kit (about $880) when you want a serviceable, high-angle joint built for hard off-road and long-haul durability.

Both restore correct ball-joint angle and caster once you add 2โ€“3.5 inches of front height, and both bolt to the factory K2XX frame mounts with no cutting. The ICON kit is not compatible with Magnetic Ride Control, so verify your suspension type before ordering.

Shop Our Top Pick โ†’

Upgrading the upper control arms on a 2015โ€“2020 Chevy Tahoe, GMC Yukon or Suburban is the single most important move once you level or lift the front end. The factory stamped-steel or cast-aluminum arms were engineered for stock ride height, so the moment you add a leveling kit or a 2โ€“3.5 inch lift, the ball joint over-angles, caster drops, and you run out of alignment adjustment. In this comparison we put two of the most popular K2XX upper control arm kits head to head: the budget-friendly Superlift 3600 cast arms (around $250) and the premium ICON 78601DJ tubular arms with the patented Delta Joint (around $880). At NLP Performance in Tampa, FL, these are the two kits our customers cross-shop most for a leveled full-size GM SUV.

Why Does a Leveled Tahoe or Yukon Need New Upper Control Arms?

A leveled or lifted Tahoe, Yukon or Suburban needs aftermarket upper control arms because raising the front suspension forces the factory arm and ball joint past their designed operating angle. The 2015โ€“2020 GM full-size SUVs (the K2XX platform shared with the 2014โ€“2018 Silverado and Sierra 1500) use an independent front suspension with a coil-over strut. When you add 1โ€“2 inches with a leveling kit โ€” or 2โ€“3.5 inches with a full lift โ€” three problems appear:

  • Ball-joint bind: the stock upper ball joint angles beyond its intended range, which accelerates wear and can limit droop (down travel) on the trail.
  • Lost caster: raising the front reduces positive caster, which shows up as wandering, vague on-center steering and reduced high-speed stability. Aftermarket arms are built with added caster to restore straight-line tracking.
  • No alignment range left: the factory cam bolts run out of adjustment, so an alignment shop cannot pull the numbers back into spec with the stock arms installed.

Aftermarket upper control arms fix all three by relocating the ball joint and adding caster, while also clearing room for the coil-over strut at full compression and making space for 33โ€“35 inch tires. For a snow-state daily driver running a taller all-terrain in winter, correct geometry also means predictable steering when the roads turn to slush. Both kits in this guide are a direct bolt-on to the factory frame mounts.

Upper control arm geometry correction for a leveled 2015-2020 Chevy Tahoe front suspension

Raising the front changes ball-joint angle and caster; aftermarket arms restore both.

Superlift 3600 Cast Upper Control Arms (Best Value)

The Superlift 3600 is the best-value upper control arm kit for a 2015โ€“2020 Tahoe, Yukon or Suburban 4WD running 2โ€“3.5 inches of front lift. Sold as a front pair for around $250, it uses a high-strength cast arm with a pre-installed OE-style ball joint, so there is nothing to press in and no special tooling required. Superlift, a suspension builder since 1975, backs the arms with its limited lifetime warranty. These arms are designed to be run with a taller lift than a simple leveling kit, giving you the extra ball-joint correction a 3.5 inch front needs.

Superlift 3600 cast upper control arms for 2015-2020 Chevy Tahoe GMC Yukon Suburban 4WD

Superlift

Superlift 15-20 Tahoe / Yukon / Suburban 4WD 2-3.5in Lift Upper Control Arms (Pair)

$251.99
Part Number slf3600PR
Fitment 2015โ€“2020 Tahoe, Yukon / Yukon XL, Suburban 1500 (4WD)
Warranty Superlift Limited Lifetime
Shop Now at NLP Performance

What We Like

  • + Around $250 for a front pair โ€” roughly a third of the price of premium tubular arms
  • + Pre-installed OE-style ball joint; no press tooling and a bolt-on install
  • + Purpose-built for a taller 2โ€“3.5 inch lift and backed by a limited lifetime warranty

Things to Consider

  • โ€“ Sealed OE-style ball joint is replaced, not rebuilt, at the end of its life
  • โ€“ Tuned for a 2โ€“3.5 inch lift rather than a mild 1 inch level

ICON 78601DJ Tubular Upper Control Arms with Delta Joint (Premium Pick)

The ICON 78601DJ is the premium upper control arm kit for the 2015โ€“2020 Tahoe, Yukon and Suburban, built around ICON's patented Delta Joint. At around $880 for the pair, it is the choice for owners who want maximum durability and a serviceable joint. The Delta Joint is a heavy-duty, high-angle ball joint that blends the durability of a traditional ball joint with the articulation of a uniball โ€” without the uniball's main weakness of exposure to dirt and water. ICON wraps the joint in a zinc-plated housing for corrosion resistance, seals it against the elements, and makes it greasable so it can be serviced rather than thrown away. The arm itself is tubular steel with polyurethane bushings and a press-in, threaded-stud ball joint, and the geometry is optimized for 1โ€“3 inches of front lift over stock.

ICON 78601DJ tubular upper control arms with Delta Joint for 2014-2020 GM 1500 Tahoe Yukon Suburban

ICON

ICON 14-18 GM 1500 Tubular Upper Control Arm Delta Joint Kit (Large Taper)

$879.95
๐Ÿ”ฅExtra 10% off
Part Number 78601DJ
Fitment 2014โ€“2020 GM 1500, incl. 2015โ€“2020 Tahoe / Yukon / Suburban (non-MagneRide)
Warranty ICON Limited Lifetime
Shop Now at NLP Performance
ICON Delta Joint high-angle sealed greasable ball joint detail for GM 1500 upper control arm

ICON's Delta Joint pairs ball-joint durability with uniball articulation in a sealed, greasable housing.

What We Like

  • + Patented Delta Joint is sealed, greasable and rebuildable โ€” built to last on a daily-driven SUV
  • + Tubular steel arm with high-angle articulation for serious off-road droop
  • + Zinc-plated, corrosion-resistant housing ideal for salt-belt and snow-state trucks

Things to Consider

  • โ€“ Around $880 โ€” roughly 3.5 times the Superlift's price
  • โ€“ Not compatible with Magnetic Ride Control and not recommended for Hybrid models

Superlift vs ICON: Head-to-Head Comparison

The quick answer: the Superlift 3600 wins on value and is purpose-built for a taller 2โ€“3.5 inch lift, while the ICON 78601DJ wins on joint technology and long-term serviceability. Both are a direct bolt-on to the 2015โ€“2020 Tahoe, Yukon and Suburban front frame mounts and both add caster to recover steering feel after a level or lift. The table below lines up the specs that actually drive the buying decision.

Kit Ball Joint Best Lift Range Arm Material Price
Superlift 3600 (Pair)Top Value OE-style, sealed 2โ€“3.5 in Cast $251.99
ICON 78601DJ Delta Joint Delta Joint (greasable) 1โ€“3 in Tubular steel $879.95

Key Specifications โ€” Superlift 3600 (Top Value)

$251.99
Front Pair
2โ€“3.5 in
Lift Range
4WD
2015โ€“2020 Tahoe/Yukon/Suburban
Lifetime
Limited Warranty
ICON 78601DJ tubular upper control arm kit with Delta Joint for 2015-2020 GM full-size SUV

The ICON 78601DJ pair is the premium, serviceable upgrade for hard-use Tahoe and Yukon builds.

Which Upper Control Arm Should You Buy?

Choose the Superlift 3600 if you are running a 2โ€“3.5 inch lift and want the strongest value โ€” it delivers the ball-joint correction a taller front needs for around $250 and installs without special tools. Choose the ICON 78601DJ if you daily-drive the truck hard, wheel it off-road, or live in the salt belt and want a sealed, greasable joint you can service instead of replace. Use these quick scenarios:

  • Budget leveled daily driver: Superlift 3600. You get correct geometry and tire clearance for roughly a third of the premium price.
  • Overland or off-road build: ICON 78601DJ. The high-angle Delta Joint allows more droop and shrugs off mud, water and road salt.
  • Winter / snow-state truck on taller all-terrains: either works, but the ICON's zinc-plated, sealed joint resists corrosion from brined winter roads.
  • Denali, High Country or any trim with Magnetic Ride Control: neither of these specific kits โ€” confirm your suspension type, because the ICON 78601DJ is not MagneRide-compatible.
Superlift 3600 cast upper control arm pair detail for leveled K2XX GM full-size SUV

The Superlift 3600 ships as a front pair with the ball joint pre-installed for a bolt-on job.

Fitment and Installation Notes

Both kits are a direct, bolt-on fit for the 2015โ€“2020 Chevrolet Tahoe and Suburban and the GMC Yukon and Yukon XL in 4WD, mounting to the factory K2XX frame brackets with the OE cam bolts. Before you order, confirm two things on your specific truck. First, the suspension type: these GM full-size SUVs left the factory with either cast-aluminum or stamped-steel control arms, and the ICON 78601DJ is engineered for those non-electronic setups โ€” it is not compatible with Magnetic Ride Control (MagneRide), which is common on Denali, High Country and some Premier and Z71 trims, and is not recommended for Hybrid models. Second, plan on a professional alignment immediately after install; the whole point of new upper arms is to restore caster and camber into spec once the front is raised. Budget 2โ€“3 hours of shop time per axle set plus the alignment.

ICON 78601DJ tubular upper control arm with polyurethane bushings for 2015-2020 Tahoe Yukon

ICON's tubular arm uses polyurethane bushings and a press-in, threaded-stud Delta Joint.

Superlift upper control arm kit hardware for 2015-2020 GM full-size SUV lift
ICON Delta Joint upper control arm zinc-plated housing for corrosion resistance

Frequently Asked Questions

Do I need upper control arms to level my 2015-2020 Tahoe?

A mild 1 inch level can sometimes stay in alignment spec on the stock arms, but anything past about 1.5โ€“2 inches of front lift needs aftermarket upper control arms on a 2015โ€“2020 Tahoe, Yukon or Suburban. New arms restore caster and relocate the ball joint so an alignment shop can pull the numbers back into spec, and they add clearance for 33โ€“35 inch tires. The Superlift 3600 is built specifically for the 2โ€“3.5 inch lift range.

What is ICON's Delta Joint and is it better than a ball joint?

The Delta Joint is ICON's patented high-angle ball joint that combines a ball joint's durability with a uniball's articulation. Unlike a bare uniball, it uses a sealed, zinc-plated, greasable housing that keeps out dirt, water and road salt, so it is better suited to a daily-driven or snow-state truck than an exposed uniball. For most street-and-trail Tahoe or Yukon builds it is the most durable joint of the two kits here.

Will these upper control arms fit a Tahoe or Yukon with Magnetic Ride Control?

No. The ICON 78601DJ is not compatible with Magnetic Ride Control (MagneRide), and it is not recommended for Hybrid models. MagneRide is common on Denali, High Country and some Premier and Z71 trims, so verify your suspension type by VIN before ordering. Both kits in this guide are engineered for the factory cast-aluminum or stamped-steel suspension.

Superlift 3600 vs ICON 78601DJ: which is the better value?

The Superlift 3600 is the better value at around $250 versus roughly $880 for the ICON kit. For a budget leveled or lifted daily driver, the Superlift cast arms deliver the geometry correction you need for about a third of the price. Step up to the ICON 78601DJ when you want the serviceable Delta Joint, tubular construction and extra off-road articulation and are willing to pay the premium for longevity.

Do aftermarket upper control arms fit the Chevy Suburban and GMC Yukon XL too?

Yes. Both the Superlift 3600 and the ICON 78601DJ fit the 2015โ€“2020 Chevrolet Suburban 1500 and GMC Yukon XL 1500 in addition to the shorter Tahoe and Yukon, because all four SUVs share the same K2XX independent front suspension as the 2014โ€“2018 Silverado and Sierra 1500. Confirm 4WD or 2WD and your factory suspension type before ordering.

Do I need an alignment after installing new upper control arms?

Yes, always align the truck right after installing upper control arms. Raising the front and swapping arms changes caster and camber, and an alignment is what brings those angles back into spec for even tire wear and stable steering. Plan on a four-wheel alignment at a shop that can handle a lifted full-size SUV.

Ready to Upgrade Your Leveled Tahoe or Yukon?

Shop Superlift, ICON and more suspension upgrades for your 2015โ€“2020 Tahoe, Yukon and Suburban at NLP Performance.

Shop Suspension

Free shipping on select brands โ€ข Located in Tampa, FL

Best seller, Chevrolet tahoe, Comparison, Control arms, Gmc yukon, Icon, Source-product:superlift-15-20-gmc-suburban-chevy-tahoe-yukon-4wd-2-3-5in-lift-upper-control-arms-pair-front, Superlift

Leave a comment