Next Level Performance
November 15, 2026 β’ 10 min read
Our Verdict
For most 2015-2021 Subaru WRX owners, the aFe Takeda Stage-2 Pro 5R is the best value cold air intake β a fully sealed airbox, full 2015-2021 fitment, and a lower price than the Injen.
The Injen SP1209 is the premium pick if you want polished mandrel-bent aluminum and a lifetime warranty, and it also covers the full 2015-2021 run. Both are honest upgrades β just know that on a stock, direct-injection FA20DIT the real power arrives once you add a tune.
Shop Our Top Pick βThe best cold air intake for the 2015-2021 Subaru WRX comes down to a two-way fight: the aFe Takeda Stage-2 and the Injen SP1209, with K&N and AEM close behind. All four bolt onto the 2.0L FA20DIT turbo boxer β the 268-hp, 258-lb-ft engine in every VA-chassis WRX β and all four free up airflow, sharpen throttle response, and wake up the turboβs induction growl. The difference is in the filter media, the price, and the fine print on fitment. At NLP Performance in Tampa, FL, these are among the most common first mods WRX owners buy, so below we put the real specs side by side and tell you which one fits your build.
What a cold air intake actually does on a 2.0L WRX
A cold air intake replaces the WRXβs restrictive factory airbox and paper filter with a high-flow filter, a larger mandrel-bent tube, and a heat shield or sealed housing that pulls cooler, denser air from outside the engine bay. On the 2015-2021 WRX that means more airflow to the FA20DIT turbo, crisper throttle response, and a noticeably louder turbo spool and blow-off chatter.
Here is the honest part most listings skip: the FA20DIT is direct-injected and runs a closed-loop, MAF-based tune, so an intake by itself delivers modest peak-power gains on an otherwise-stock car β think single digits to low double digits of wheel horsepower, mostly in the upper rev range. The bigger wins are throttle feel, airflow headroom, and sound. The intake pays off most when it is paired with an ECU tune (a COBB Accessport or a dealer/pro tune), which recalibrates for the extra airflow and unlocks the real numbers. Buy the intake as the first step of a plan, not as a magic 30-horsepower box.
The aFe Takeda Stage-2 pairs a sealed one-piece housing with a large conical filter to feed the FA20DIT turbo.
aFe Takeda vs Injen SP1209: the head-to-head
The aFe Takeda Stage-2 and the Injen SP1209 are the two intakes WRX owners cross-shop most, and they take opposite approaches. The aFe Takeda is a fully enclosed airbox: a one-piece roto-molded housing seals the filter off from hot engine-bay air, and it ships in two filter flavors β the oiled 5-layer Pro 5R or the oil-free Pro Dry S. The Injen SP1209 is a polished mandrel-bent aluminum tube with an open filter behind a heat shield, built around Injenβs MR Technology (a tuned air gap designed to broaden the midrange) and backed by a Limited Lifetime Warranty.
On price, the aFe Takeda Pro 5R lands around $400 and the Injen around $540, so the aFe is the value play while the Injen is the show-and-shine premium choice. Both carry full 2015-2021 WRX fitment in a single part number, which matters: it means you can order either one without worrying about which model year or facelift you have. Here is how the full field stacks up.
| Intake | Filter | Fitment (WRX 2.0L) | Warranty | Price |
|---|---|---|---|---|
| aFe Takeda Stage-2 Pro 5RTop Pick | Oiled 5-layer cotton, sealed box | 2015-2021 | Limited, washable filter | $399.00 |
| Injen SP1209 Polished | Washable, open w/ heat shield | 2015-2021 | Limited Lifetime | $543.07 |
| aFe Takeda Stage-2 Pro Dry S | Oil-free 3-layer, sealed box | 2015-2021 | Limited, washable filter | $410.00 |
| K&N Typhoon 69-8011TTKBudget | Oiled cotton, heat shield | 2018-2020 | 10-Yr / Million Mile | $315.90 |
| AEM 21-732C Cold Air | AEM Dryflow, oil-free | 2015-2020 | Limited Lifetime | $369.99 |
The five best 2015-2021 WRX intakes, reviewed
What We Like
- + Fully sealed airbox keeps hot air out
- + Best price of the premium intakes (around $400)
- + Single part number fits all 2015-2021 WRX 2.0L
Things to Consider
- β Oiled filter must be re-oiled sparingly to protect the MAF
- β Big airflow gains need a tune to be realized
What We Like
- + Show-quality polished aluminum tube
- + Injen Limited Lifetime Warranty
- + MR Technology tuned for midrange torque
Things to Consider
- β Priciest option here (around $540)
- β Open-filter design is less sealed than the aFe box
Injenβs polished aluminum tube and heat shield are the show-and-shine pick in the WRX engine bay.
K&Nβs washable cotton-gauze filter is the budget route to a reusable intake.
2015-2021 WRX Key Specs
Oiled vs dry filter: which is right for a direct-injection WRX?
On a direct-injection WRX, a dry (oil-free) filter is the safer, lower-maintenance choice. The FA20DIT meters airflow with a MAF sensor, and the concern with any oiled cotton-gauze filter is over-oiling: excess filter oil can migrate downstream and coat the hot-wire MAF element, which can skew fuel trims and, in rare cases, trip a check-engine light. A dry synthetic filter β the aFe Pro Dry S or the AEM Dryflow β removes that variable entirely because there is no oil to migrate.
That does not make oiled filters a bad choice. The aFe Pro 5R and K&N Typhoon both use proven oiled cotton-gauze media that many thousands of WRX owners run without issue β the rule is simply to oil lightly and only when the filter is actually dirty, following the kitβs instructions. If you would rather never think about it, go dry; if you want maximum filtration surface and do not mind occasional maintenance, oiled is fine.
A dry synthetic filter like AEMβs Dryflow skips the oiling step β a plus on a MAF-based WRX.
Do you need a tune with a WRX intake?
You do not strictly need a tune to run any of these intakes safely, but you should plan on one to see real power. These sealed and heat-shielded kits are designed to work with the factory calibration out of the box, so a stock WRX will run fine with better throttle response and louder induction. The catch is that the stock ECU tune limits how much of the extra airflow becomes power. Add a COBB Accessport with an off-the-shelf or custom Stage-1/Stage-2 map and the same intake suddenly contributes meaningful horsepower and torque, safely, because the fueling and boost are recalibrated for it.
Our advice at the shop: budget the intake and the tune together. The intake is the right first hard part, and it becomes the foundation for a downpipe, bigger intercooler, and the rest of a Stage-2 build down the road.
Installation and what to expect
Installing a WRX cold air intake is a one- to two-hour driveway job with basic hand tools. You will remove the factory airbox and intake tube, transfer or relocate the MAF sensor into the new tube, mount the heat shield or sealed housing, and clamp everything down. The most important steps are seating the MAF sensor squarely so it reads airflow accurately and double-checking every clamp for a leak-free seal β a loose coupler on a turbo car can cause rough idle or trim codes. After install, reset the ECU and take it easy for the first few miles while the car relearns its fuel trims. Expect a sharper throttle, a louder turbo whoosh and blow-off flutter, and a mild bump in top-end response even before a tune.
Frequently Asked Questions
What is the best cold air intake for a 2015-2021 Subaru WRX?
The aFe Takeda Stage-2 Pro 5R is the best overall value, at around $400 with a fully sealed airbox and a single part number that fits every 2015-2021 WRX 2.0L. The Injen SP1209 is the premium alternative with polished aluminum and a lifetime warranty, and the K&N Typhoon is the budget pick at under $320 for 2018-2020 cars.
How much horsepower does an intake add to a WRX?
On a stock 2015-2021 WRX (268 hp / 258 lb-ft), a cold air intake alone typically adds only a few wheel horsepower, mostly in the upper rpm range, plus better throttle response and induction sound. The meaningful gains come when the intake is paired with an ECU tune such as a COBB Accessport, which recalibrates the car for the added airflow.
aFe vs Injen: which WRX intake is better?
The aFe Takeda is the better value and uses a fully sealed airbox, while the Injen SP1209 is the premium pick with a polished aluminum tube and a Limited Lifetime Warranty. Choose the aFe Pro 5R (or oil-free Pro Dry S) to save about $140; choose the Injen for the show finish and lifetime coverage. Both fit all 2015-2021 WRX 2.0L.
Do I need a tune to run a cold air intake on my WRX?
No, these intakes are designed to run safely on the stock ECU tune, so you can install one without a tune. But to actually gain power you should add a tune (such as a COBB Accessport Stage-1 or Stage-2 map), which recalibrates fueling and boost for the extra airflow.
Will an intake fit my 2015-2017 WRX, or just the 2018-2021?
The aFe Takeda Pro 5R, aFe Pro Dry S, and Injen SP1209 all use one part number that covers the full 2015-2021 WRX 2.0L. The AEM 21-732C fits 2015-2020. The K&N Typhoon 69-8011TTK shown here fits 2018-2020; for a 2015-2017 WRX, order K&N part number 69-8006 instead.
Oiled or dry filter for a direct-injection WRX?
A dry filter is the safer choice on the direct-injection FA20DIT because there is no filter oil that can migrate onto the MAF sensor. The aFe Pro Dry S and AEM Dryflow are oil-free; the aFe Pro 5R and K&N Typhoon use oiled cotton-gauze that is perfectly reliable as long as you oil it lightly and only when the filter is dirty.
Ready to Wake Up Your WRX?
Shop aFe, Injen, K&N, AEM, and more cold air intakes for the 2015-2021 Subaru WRX at NLP Performance.
Shop Cold Air IntakesFree shipping on select brands β’ Located in Tampa, FL
Looking to go further? Pair your intake with a tune and supporting mods from our engine performance collection to build a proper Stage-2 WRX.